U Slot Patch Antenna Design

  
U Slot Patch Antenna Design 3,5/5 4591 votes

Wireless local-area networks (WLANs) at 5 GHz offer the impressive data rates (54 Mb/s) that have helped them grow in popularity. The broad bandwidth of these systems—from 5.15 to 5.85 GHz—also poses a challenge for RF circuit and antenna designers. Fortunately, it is possible to cover the full 5-GHz band using a compact patch antenna.

Traditionally, patch antennas are limited in bandwidth, typically less than 5 percent. But numerous approaches have been developed to increase the bandwidth of a patch antenna, including the use of a U-shaped slot cut into the patch.1,2 A set of design equations has been derived for the purpose of determining the dimensions of the slot relative to the patch size, and these equations have shown good accuracy compared to measured results.2

Figure 1 shows an example of a wideband antenna with a U-shaped slot for 5-GHz use. The antenna patch is 1.719 in. Long and 0.866 in. With a height of only 3.5 mm, it is designed for low-profile applications, such as in computer WLAN cards. The patch antenna is fed with a probe near the patch. The U-slot patch antenna was originally developed as a single-layer, single-patch wideband antenna. It has recently been shown that it can also be designed to perform a number of other functions. In this paper, a comprehensive account is given on the development of this antenna. This technique is a modified version of a U-slotted patch antenna. Coupled slots parallel to both ends, arms, of the U-shaped slot are added to enhance the bandwidth. The proposed structure is simulated using IE3DTMand SonnetTM, commercial software packages, and implemented using a foam substrate (εr≈1). The basic U -slot loaded rectangular micro strip patch antenna design is seen in below Figure. Here, L is the patch length, W is the patch width, F is the feed point, Ls is the vertical slot length, Ws is the horizontal slot length, tL and tW are slot widths in the vertical and horizontal, respectively.

Slot

Figure 1 shows an example of a wideband antenna with a U-shaped slot for 5-GHz use. The antenna patch is 1.719 in. long and 0.866 in. wide. With a height of only 3.5 mm, it is designed for low-profile applications, such as in computer WLAN cards. The patch antenna is fed with a probe near the patch's center. The slot, which is 0.022 in. wide, is cut symmetrically around the RF feed point. The antenna structure is extremely simple, yet offers good RF performance. Figure 2 shows the antenna's return loss, better than 10 dB. The plot shows that the antenna can easily cover a range of 5 to 6.5 GHz with its 26.5-percent bandwidth.

The addition of resonant modes helps to increase patch-antenna bandwidth. Once the multiple resonant points are created, they can be placed at optimized positions for good performance. In the design of Fig. 1, a total of two such resonant points is more than enough to achieve the bandwidth goals for 5-GHz WLAN operation. The total bandwidth and the depth of the combined resonance can be controlled by moving each of the two resonant points closer together or further apart. When the resonant points are closer, the bandwidth is smaller and antenna is better matched to 50 Ω. As the resonant points are spread further apart, the bandwidth increases but the antenna is less matched to 50 Ω.

Antenna

The patch itself provides one resonant point. The U-shaped slot is another resonant point. The U-shaped slot essentially forces current to flow in a different path on the patch. Each path of current flow corresponds to a resonant point. Once the equivalent current-flow path is determined, it can be easily converted back to the resonant frequency based on its length. This is the basic theory behind this type of antenna. Figures 3 and 4 display the current flow at the two resonant points in the patch antenna. At 5.3 GHz, RF current flows up first, then returns to the feed point. At 6.3 GHz, RF current flows down first. Detailed derivation of the design equation is contained in ref. 2 and will not be repeated here. Since the design is an iterative process, it is possible to compile the design equations from ref. 2 into a MathCAD program. For clarity, the notation of that original reference has been followed here,2 with the MathCAD file shown in Fig. 5. All dimensions are in metric units.

The derived equations, developed by observing the RF current-flow paths on a patch antenna, were used as starting points for the U-shaped patch antenna design. Numerous rounds of simulations were performed for optimizing the design. For this optimization purpose, the IE3D three-dimensional (3D) electromagnetic (EM) simulation software from Zeland Software (Fremont, CA) was used in modeling the patch antenna. Each simulation run required about 20 minutes with good accuracy on a standard personal computer (PC).

Patch Antenna Design Calculator

The U-shaped patch antenna's radiation pattern is shown in Fig. 6, with the directional pattern typical of patch designs. Simulated maximum antenna gain is close to 9.5 dBi. Because of its compact size, generous bandwidth, and high gain, the U-shaped patch antenna is well suited for point-to-point applications in 5-GHz WLAN systems.

ACKNOWLEDGMENT
The author greatly appreciates the technical supports provided by Dr. Jiang-X Zheng of Zeland on IE3D software. IE3D is a trademark of Zeland Software. Mathcad is a registered trademark of MathSoft, Inc.

Abstract—A novel design of patch antenna is presented with double U slot structure on patch with ground irregularities. As a result tri-band response is achieved with gain reaching 0.785 to 3.75dB respectively and directivity of 5.5 to 5.6dBi. Coaxial cable is mounted with patch as medium of power. The antenna has.

REFERENCES

Slot Antenna For Hf

  1. T. Huynh and K.F. Lee, 'Single-layer single-patch wideband microstrip antenna,' Electronics Letters, Vol. 31, No. 16, August 3, 1995.
  2. R. Bhalla and L. Shafai, 'Resonance behavior of single U-Slot microstrip patch antenna,' Microwave and Optical Technology Letters, Vol. 32, No. 5, March 5, 2002.
Ultra wide band is rapidly advancing as a high data rate wireless communication technology. As is the case in conventional wireless communication systems, an antenna also plays a very crucial role in UWB systems. However, there are more challenges in designing a UWB antenna than a narrow band one. A suitable UWB antenna should be capable of operating over an ultra-wide bandwidth as allocated by the FCC. At the same time, satisfactory radiation properties over the entire frequency range are also necessary. This thesis focuses on UWB antenna design and analysis. Studies have been undertaken covering the areas of UWB fundamentals and antenna theory. In recent years, the U-slot patch antenna established itself as a versatile, low profile and cost effective antenna that can be finetuned for ultra-wideband operations. The main objective of this thesis is to propose an effective practical design procedure to design U-Slot antenna and provide physical insight into the design using full wave analysis methods. This research work focuses on developing a novel scheme to design wideband U-Slot antenna. To validate the design technique antenna is fabricated and measured results are compared with the simulated to assess the performance. In this dissertation, effect of reactive loading on probe fed, single layer, U-Slot loaded microstrip antenna is investigated using Theory of Characteristic Modes (TCM). Detailed analysis of reactive loading due to feed location and arm-angle variation is presented. Optimized reactive loading has been shown to produce a modified U-Slot structure without increasing any cost and complexity. The optimized loaded antennas are wideband with a relatively stable radiation pattern. Furthermore, we propose an optimization guideline for a wide band design with stable radiation patterns.